New Holland FP240
![](/assets/Uploads/NH-FP240-2019.jpg)
Features
PT Forage Harvesters
BEST IN HIGH CAPACITY AND CHOP QUALITY
No one builds rugged, high-capacity forage harvesters like New Holland. The best-selling line of pull-type models provides the uniform chopping you're looking for and all the reliability you've come to expect from New Holland.
CROP FLOW
UNIFORM CUT LENGTH IS KEY
A uniform length of cut not only yields high-quality feed, it makes everything easier—unloading, blowing, storing and feeding. The key to a consistent chop is smooth crop flow through the forage harvester. It's a process New Holland has perfected and it's what makes these forage harvesters so effective.
SHARPENING AND ADJUSTMENT
FEATURES TO KEEP YOU CHOPPING AT PEAK EFFICIENCY
Chop quality is the hallmark of New Holland forage harvesters due to the built-in features that help to maintain them. Knife sharpening and shearbar adjustment are a snap and the cutterhead reverses to ensure a true cutting edge on all knives.
CROPPRO™ CROP PROCESSOR
ONE-PASS CORN SILAGE PROCESSING
Improve your corn silage feed efficiency with New Holland's optional onboard CropPro™ crop processor. Factory-installed between the cutterhead and blower, it shears cobs and stems, and cracks and crushes kernels, producing silage that is higher in effective fiber and easier for the herd to digest.
METALERT® III
PROTECT EQUIPMENT AND CATTLE
Broken rake tines, sickle sections and lost hitch pins can turn up in the cleanest fields. Large pieces can cause costly cutterhead damage, while smaller pieces can end up in livestock feed and harm animals. An easy way to avoid these dangers is to install the Metalert® III electronic metal detector on your forage harvester.
HEADERS
WIDE SELECTION OF CROP-SAVING HEADERS
Keep pace with the high-capacity demands of New Holland forage harvesters by choosing the right crophead. All are PTO shaft-driven for easier hookup and removal. Shaft drive provides increased reliability and less maintenance than chain drives.
Specifications
FP240 | |
Optional CropPro™ Crop Processor | |
Optional CropPro™ Crop Processor | Optional |
Construction | Hardened ductile iron, steel shaft |
Weight, lbs. (kg) | 520 lbs (231kg) |
Roll width, in. (mm) | 26-7/8" (682.6 mm) |
Roll diameter, in. (mm) | 7-7/8" (200 mm) |
Roll gap, in. (mm) | 3/16" to 5/8" (4.8 to 15.9 mm) |
Roll speed | 2650 rpm upper, 2250 rpm lower |
Specifications | |
Weight (single axle), lbs. (kg) | 4700 (2130) |
Length, ft. in. (m) | 21' 6" (6.5 m) |
Height with standard spout, ft. in. (m) | 11' 2" (3.4 m) |
Width, ft. in. (m) | 10' 8" (3.3 m) |
Number/type of knives | 12 single-edge hardened alloy |
Cutterhead, type/speed | Cylinder, 850 rpm |
Cutterhead, diameter, in. (mm) | 21" (533.4 mm) |
Throat opening, in. (mm) | 22" x 6-5/8" (558.8 mm x 167.7 mm) |
Shearbar | Quick adjust, reversible, hard-faced on vertical and horizontal surfaces |
Length of cut, in. (mm) | 3/16" to 7/16" (76.2 to 177.8 mm) |
Blower speed | 1000 rpm |
Recommended max. tractor hp | 300 hp |
Minimum power required | 180 PTO hp |
Knife sharpener | 3" manual, built-in |
Recutter screens (non processor units) | 6 sizes available |
Vertical wheel adjustment, in. (mm) | 6" (152 mm) |
Tire sizes, single axle | 14Lx16.1 8PR standard |
Tire sizes, tandem axle | 11Lx15-156PR |