Land Pride RC4715

New Products / Land Pride / Rotary Cutters / RC4715 Rotary Cutters / RC4715

Double tap to zoom

Features
Specifications

Features

Features	Benefits
Surpassed rugged industry standards	All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.
Factory assembled	Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.
Rugged heavy built gearboxes	Capable of handling heavy cutting applications.
Gearbox seal protection	Gearbox bottom seal protection for longer bearing life.
Sliding guard for splitter gearbox	Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance.
2 Piece driveline shields	Driveline grease zerks are easier to access.
Low hitch weight on tractor tongue	Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.
Narrow A-frame hitch	Allows for a tighter turning radius.
Adjustable park jack angle	Park jack can be adjusted to be perpendicular to the ground.
Adjustable driveline hanger	Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft.
Input driveline: Cat. 6 CV	Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
Drivelines with slip-clutches: Cat. 4 intermediate Cat. 4 or Cat. 5 wings	Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles.
Grease zerks on end caps of driveline	Intermediate and wing driveline cross journals are easier to grease.
High blade tip speed	Allows clean cutting of material.
6" Blade overlap	Eliminates skipping during turns.
Diamond blade bar	Provides the critical strength needed for consistent, top performance.
3/16" Round stump jumper	Standard thick stump jumper material keeps damage to a minimum.
Smooth top design	Reduces accumulation of debris and is easier and faster to clean.
Tops of decks are 100% welded	Makes center decks and wing decks stronger.
1/4" Sidewall thickness	Increased thickness reduces damage from objects being thrown into deck sidewalls.
Multiple center skid shoe locations	Run two or four skid shoes in locations under the tongue pivots or out at the wing hinges.
Beveled skid shoes on wings	Reduces gouging the ground when turning.
LED signal lights	LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.
Hinged wing sections	Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
1" Solid hinge rods	Larger diameter hinge rod provides greater strength in the hinge area.
Wing transport lock pins	Transport lock pins will hold wings in folded position in the event of hydraulic loss.
Enclosed dual 1" leveling rods	Cutter pulls equally on the rear axle while traveling over rough terrain.
5-Bolt hubs	5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims	Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.
Spring cushioned center-axle	Protects unit from bumps and ground shock.
Optional spring cushioned wing-axles	Further improves ride over a multitude of terrains.
Replaceable individual wheel spindles	Spindles can be replaced when damaged without replacing entire axle assembly.
Wheel options	Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can’t go flat.
LP Performance hitch option	Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions.
Bar-tite hitch option	Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.

Specifications

Specifications & Capacities	RC(M)4715 & RCG(M)4715
Horsepower range	55 - 250 hp
Gearbox horsepower	540 rpm or 1000 rpm 250hp (186.4 kW) Divider and 210hp (156.6 kW) Center & Wings
Gearbox lubrication	Gear Lube 80-90W EP
Gearbox oil capacity	Splitter: 3.5 pints (1.66 L); Center deck & Wings: 6 pints (2.84 L)
Cutting capacity	4" (10.2 cm)
Machine weight Total weight Tongue weight	5,000 lbs. (2268 kg) 1860 lbs. (843.7 kg)
Blade tip speed At 540 rpm At 1000 rpm	Center Blades & Wing Blades = 16,300 FPM (82.8 mps) Center Blades = 16,300 FPM (82.8 mps) & Wing Blades = 16,000 FPM (81.3 mps)
Hitch types	Swivel Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch.
Hitch jack	Standard (7,000 lbs.) (3175.1 kg)
Signal lights 7 Pin connector	LED SAE J560 pin configuration
Cutting width Overall width Transport width with 21" tires	15'-0" (4.57 m) 15'-10" (4.83 m) 10'-3" (3.12 m) - Single-acting fold option, 7’-3" (2.21 m) - Dual-acting fold option.
Overall length	16'-3" (4.95 m) - With center deck raised fully up.
Deck height	12" (30.5 cm)
Cutting height	1-1/2" - 16" (3.8 cm - 40.6 cm) - Varies by tire option.
Lift hydraulics	3" x 8" (7.6 cm x 20.3 cm) hydraulic cylinder, hoses, fittings & stroke control spacers.
Wing hydraulics	2 1/2" x 12" (6.4 cm - 30.5 cm) hydraulic cylinders, hoses & fittings.
Wing transport protection	Wing Transport Lock Pins
Deck material thickness	10 Gauge (3.4 mm)
Side skirt thickness	1/4" (6 mm) Steel
Skid shoes	Wing Deck: 1 Replaceable skid shoe per wing. Center Deck: 2 Replaceable skid shoes and multiple mounting locations.
Blades - 6 (2 per carrier)	1/2" x 4" (1.3 cm - 10.2 cm) Heat-treated, free-swinging alloy steel with uplift.
Blade overlap	6" (15.2 cm)
Blade bolt	Keyed with hardened flat washer & locknut.
Stump jumper / blade holder	3/16" (5 mm) Thick round dish shaped pan, reinforced with 1" x 4" (2.5 x 10.2 cm) blade bar.
Front & rear guards	Optional single row chain or dual row chain.
Input driveline 540 & 1000 rpm	Cat. 6 with constant velocity u-joint with or without overrunning clutch.
Intermediate driveline	Standard - Category 4 with slip-clutch.
Wing drivelines	Standard - Category 4 with slip-clutch or Category 5 with slip-clutch.
Wheel options	21" (53.3 cm) or 26" (66 cm) Laminated tires 24" (61 cm) Used aircraft, foam filled tires 25.5" (64.8 cm) 20 ply tires, foam filled or pneumatic 29" (73.7 cm) Used aircraft tires
Number of wheels	6 - Wheel option: Four on transport axle and one on each wing axle. 8 - Wheel option: Four on transport axle and two on each wing axle.
Transport axle	Many configurations to choose from.
Hubs	Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.
LP Performance hitch & Bar tite hitch pivot shaft diameter	2 1/4" (5.7 cm)
A-frame tongue	5" x 3" (12.7 cm x 7.6 cm) rectangular tubing