Land Pride RC3614

New Products / Land Pride / Rotary Cutters / RC3614 Rotary Cutters / RC3614

Double tap to zoom

Features
Specifications

Features

Features	Benefits
Surpassed rugged industry standards	All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures.
Factory assembled	Saves customer set-up time and money. Adjustments should always be made by dealer.
250 HP divider gearbox 130 HP center & wing gearboxes	A rugged heavy-built gearboxes capable of handling heavy-cutting applications.
Gearbox Seal Protection	Gearbox bottom seal protection for longer bearing life.
2" Output gearbox shaft	Large output shaft handles shock loads better.
Input driveline: Cat. 6 CV or Cat. 5 Conventional	Holds up to shock loads and harsh mowing conditions. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
Easy Greasable drivelines	Drivelines have access holes for greasing the U-joints and to grease the inner profiles.
2 or 4 Plate slip-clutch	Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered.
High blade tip speed	Allows clean cutting of material & even distribution. See Specifications for actual FPM.
6" Blade overlap	Eliminates skipping during turns.
Good cutting capacity	Can cut brushy areas with saplings up to 2".
13" Deck height	Handles heavy cutting, which reduces balling-up of cut material under the deck.
10 Ga. stump jumper backed with a 1" x 4 1/2" thick blade mounting bar	Heavy round stump jumper for protecting the gearbox seal and gearbox output shaft. Can hold up to tough conditions.
Spindle Nut Protected	Spindle nut and threads extending beyond the nut are guarded to protect against damage from hitting solid objects.
10 gauge smooth deck top	Reduces accumulation of debris and is easier and faster to clean.
1/4" side skirt	Reduces debris piercing possibilities.
Self-leveling hitch	Reduces drawbar wear by keeping hitch level while going through ditches.
Hinged wing section	Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
1" Solid hinge rod	Larger diameter hinge gives greater strength to cutter and hinge area.
Wing transport lock	Holds transport wing in the folded-up position in case of hydraulic pressure loss.
Enclosed front to rear dual leveling rods	Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod.
5-Bolt hubs	5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims	Allows water to drain from wheels mounted on the folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims.
Spring-cushioned center axle	Protects unit from bumps and ground shock, cushions loads on drawbar.
Replaceable wheel spindles	Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove one bolt to replace damaged spindle.
Rephasing lift cylinders	Allows cutter to be leveled using hydraulic cylinders verse mechanical turnbuckles.
7/8" Leveling rods	Large diameter leveling rods provide superior supporting strength over rough terrain.
Double swivel hitch option	Great for uneven terrain, reduces drawbar wear. Must use spacer washers on drawbar.
Bar-tite hitch option	Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
LED Signal lights	LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts.
Wheel options	Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting & can’t go flat.
Deck rings (optional)	Keeps blades from damaging the deck.

Specifications

Specifications & Capacities	RC3614
Tractor horsepower	70 to 160 hp
Gearbox horsepower	250 hp Splitter 130 hp Center & Wing
Gearbox oil capacity	5.18 Pints: Divider Gearbox 6.76 Pints: Center deck, LH deck & RH deck spindle gearboxes
Gearbox lubrication	Gear Lube 80-90W EP
Cutting capacity	2"
Machine weight hitch weight total weight	Chain guards, 5 AC tires and standard clevis. 2,220 lbs. 5,620 lbs.
Blade tip speed	16,500 fpm
Hitch types	Optional Self-Leveling Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Pintle Hitch, or Ball Hitch
Hitch jack	Standard (7,000 lbs.)
Signal Lights 7 Pin connector	LED SAE J5560 pin configuration
Cutting width Overall width Minimum transport width	13' - 6" 14' - 9 1/4" 9' - 2 1/2" (With cutting height at 2")
Overall length	17' - 6" (With cutting height at 2")
Deck height	13"
Cutting height*	2" to 12"
Lift hydraulics center deck right wing	3 1/4" x 8" Rephasing hydraulic cylinder with hoses, fittings & stroke control spacers. 3" x 8" Rephasing hydraulic cylinder with hoses & fittings.
Wing folding hydraulics	3" x 12" single-acting hydraulic cylinder complete with hose & fittings.
Wing flex	45o up, 20o down while cutting.
Deck material	1 - Piece, 10 gauge.
Side skirt material	1/4" plate.
Skid Shoes wing deck center deck weight box	Replaceable: 1 Standard straight skid shoe and 1 AR400 leading skid shoe Replaceable: 2 Skid shoes Reversible & replaceable: 1 Skid shoe
4 Blades (2 per carrier)	1/2" x 4" Heat Treated Free Swinging Alloy Steel with up lift.
Blade overlap	6"
Blade bolt	Keyed with hardened flat washer & locknut.
Stump jumper / blade holder	10 Gauge round dish shaped pan, reinforced with 1" x 4 1/2" blade mounting bar.
Deck ring	Optional 3/8" formed and welded.
Front & rear guards	Optional single chain or double chain.
Input driveline	ASAE Cat. 6 with constant velocity u-joint.
Intermediate & wing drivelines	Cat. 4 with slip-clutch or optional Cat. 5 with slip-clutch
Tire options	6" x 9 x 21" Laminated tires 27" x 7.75" Used aircraft tires with foam filling 29" x 9" Used aircraft tires without foam filling
Number of wheels	5 - Wheel option: 4 on transport axle and one on wing axle. 6 - Wheel option: 4 on transport axle and two on wing axle
Standard transport axle	Spring-cushioned on center transport axle.
Axle fasteners	1 1/4" Greasable pins
Hubs	Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts.
* Maximum cut height is dependent on tire options selected.